June 18, 2019, 01:43:23 AM

Author Topic: Toy's n' That....  (Read 33667 times)

0 Members and 2 Guests are viewing this topic.

Offline Lord Borak

  • Full Member
  • *
  • Posts: 261
    • Loc: United Kingdom
Re: Toy's n' That....
« Reply #300 on: May 30, 2019, 09:52:43 PM »
Well, yes, the fist isn't for everyone. It's for one person actually and he loves it. So as far as I'm concerned, mission achieved :P

I've been away for a few days so will get cracking on the Dominator Prow over the weekend. Then I'm going to start something a little special ;)

Offline osjclatchford

  • Active Member
  • *
  • Posts: 192
    • Loc: chigwell, essex, uk
Re: Toy's n' That....
« Reply #301 on: May 31, 2019, 06:35:54 AM »
Something a bit special! Like the rest of this isn't already?  ;)
2017 Droppod Studios -  A subsidiary of the OSJC

Offline Lord Borak

  • Full Member
  • *
  • Posts: 261
    • Loc: United Kingdom
Re: Toy's n' That....
« Reply #302 on: June 15, 2019, 12:24:05 AM »
Wuhoooooooo The forum is back up! What's going on??

Made a new prow for the Transporter. No idea why I didn't make a prow like this before but, meh, its done now and off to the casters with the Battleship bits. Also if anyone was wondering there's a scale shot of it next to a Dauntless.





I've also 'finished' the Tyrant. Still not sure about the antennae on the weapon batteries. Kinda looks Chaosy..... Should I remove them?



Offline Ragsta

  • Active Member
  • *
  • Posts: 15
    • Loc: Edinburgh
Re: Toy's n' That....
« Reply #303 on: June 15, 2019, 02:10:40 PM »
Iím inclined to leave the antenna - they accentuate the ships hull sides. If they come off it might end up seeming a bit skinny?  ???

I like that transport prow, will you be putting that into the set youíre selling or separately? If separate prows are on the horizon that would be awesome- I have slow burn plans for an upgraded fleet.

EDIT: Having looked again I can see where youíre coming from actually - looks good either way and itís all about what sits best with you!
« Last Edit: June 15, 2019, 02:51:21 PM by Ragsta »

Offline Lord Borak

  • Full Member
  • *
  • Posts: 261
    • Loc: United Kingdom
Re: Toy's n' That....
« Reply #304 on: June 16, 2019, 03:53:24 PM »
Yeah, I'm worried about it being skinny. Or just to bland. But at the same time...... It's quite a chaosy profile.

Right, another rescue attempt. I had two cruiser hulls in seriously bad repair. One was missing the entire front section and both had bits cut out of the hull. Rather than chuck them I decided to cobble together a Furious class grand cruiser.





Thoughts? Colour scheme ideas? Thinking bronze with a red prow.

Offline osjclatchford

  • Active Member
  • *
  • Posts: 192
    • Loc: chigwell, essex, uk
Re: Toy's n' That....
« Reply #305 on: June 16, 2019, 07:11:58 PM »
Nice but tbh I don't like that rettie prow on that cruiser. It seems out of scale and actually makes the ship look smaller (perhaps that's because I'm used to seeing it on something longer?) One of your own bs prows would suit better...
2017 Droppod Studios -  A subsidiary of the OSJC

Offline Lord Borak

  • Full Member
  • *
  • Posts: 261
    • Loc: United Kingdom
Re: Toy's n' That....
« Reply #306 on: Yesterday at 10:33:21 AM »
I saw what you meant so changed the prow. Luckily, spare prows I seem to have in abundance nowadays!



Offline Malika

  • Full Member
  • *
  • Posts: 1244
    • Loc: Netherlands
    • Bits Blitz
Re: Toy's n' That....
« Reply #307 on: Yesterday at 11:35:26 AM »
Very sleek!
Bits Blitz - the place to be for all your bits needs!

Offline osjclatchford

  • Active Member
  • *
  • Posts: 192
    • Loc: chigwell, essex, uk
Re: Toy's n' That....
« Reply #308 on: Yesterday at 06:55:17 PM »
Ah man that's tasty. That prow is spot on. Is it wrong I want one of these now too..?
2017 Droppod Studios -  A subsidiary of the OSJC