July 20, 2019, 12:19:16 AM

Author Topic: Modelling bits for 3d printing  (Read 60143 times)

0 Members and 1 Guest are viewing this topic.

Offline marell le fou

  • Full Member
  • *
  • Posts: 1107
Re: Modelling bits for 3d printing
« Reply #285 on: January 02, 2019, 09:06:03 PM »
Mmmm the artillery block is a little bit too bulky to me.

Looks too much like a cube with pointy bits. You have done better :)

Offline Malika

  • Full Member
  • *
  • Posts: 1251
    • Loc: Netherlands
    • Bits Blitz
Re: Modelling bits for 3d printing
« Reply #286 on: January 07, 2019, 04:27:44 PM »
That was kinda the idea I was going for when designing this artillery piece. I missed the big missile pods filled with tons of small missiles.
Bits Blitz - the place to be for all your bits needs!

Offline Malika

  • Full Member
  • *
  • Posts: 1251
    • Loc: Netherlands
    • Bits Blitz
Re: Modelling bits for 3d printing
« Reply #287 on: January 11, 2019, 03:50:09 PM »
Need more bits?

Novan Logistics Boxes (Supply Dump) - 4.00



Quote
A set of Novan logistics/equipment boxes consisting of the following:

4 x individual boxes sprues + 4 additional loose boxes
3 x stacked boxes sprues
https://vanguardminiatures.co.uk/shop/novan-logistics-boxes-supply-dump/
Bits Blitz - the place to be for all your bits needs!

Offline Malika

  • Full Member
  • *
  • Posts: 1251
    • Loc: Netherlands
    • Bits Blitz
Re: Modelling bits for 3d printing
« Reply #288 on: January 20, 2019, 08:52:11 AM »
Bits Blitz - the place to be for all your bits needs!

Offline marell le fou

  • Full Member
  • *
  • Posts: 1107
Re: Modelling bits for 3d printing
« Reply #289 on: January 21, 2019, 08:25:08 PM »
Looks like something flying :)

Offline Malika

  • Full Member
  • *
  • Posts: 1251
    • Loc: Netherlands
    • Bits Blitz
Re: Modelling bits for 3d printing
« Reply #290 on: January 27, 2019, 10:08:49 AM »
Yah, sadly enough it's pretty low on Vanguard's priority list since it's not a direct proxy.  ::)
Bits Blitz - the place to be for all your bits needs!

Offline Malika

  • Full Member
  • *
  • Posts: 1251
    • Loc: Netherlands
    • Bits Blitz
Re: Modelling bits for 3d printing
« Reply #291 on: January 30, 2019, 05:07:56 AM »
Need some illumination?

Wall Lights (6mm) - 2.00




Quote
Wall mountable lights set that can be glued to any flat surface on building walls or even used as ground mounted lights on runways or other landing zones.

Set contains:

30 x lights

See images for size comparison and demonstration of use, here seen on TMG plastic terrain tiles.
6mm figure shown for scale.
https://vanguardminiatures.co.uk/shop/wall-lights-6mm/

Street Lights (6mm) - 6.50



Quote
A set of city street lights in two variants, single and double lamps, (6mm scale).

Set contents 24 x street lights:

12 x single lights
12 x double lights

6mm figure show for scale.
https://vanguardminiatures.co.uk/shop/street-lights-6mm/
Bits Blitz - the place to be for all your bits needs!

Offline marell le fou

  • Full Member
  • *
  • Posts: 1107
Re: Modelling bits for 3d printing
« Reply #292 on: January 30, 2019, 08:43:33 PM »
Could be used as pipes, too.

Offline Malika

  • Full Member
  • *
  • Posts: 1251
    • Loc: Netherlands
    • Bits Blitz
Re: Modelling bits for 3d printing
« Reply #293 on: February 10, 2019, 09:31:57 AM »
Bits Blitz - the place to be for all your bits needs!

Offline marell le fou

  • Full Member
  • *
  • Posts: 1107
Re: Modelling bits for 3d printing
« Reply #294 on: February 10, 2019, 07:32:18 PM »
Looks like an orc walker ? Or mechanicus ?

Offline Malika

  • Full Member
  • *
  • Posts: 1251
    • Loc: Netherlands
    • Bits Blitz
Re: Modelling bits for 3d printing
« Reply #295 on: February 11, 2019, 05:49:22 PM »
« Last Edit: February 15, 2019, 08:29:21 AM by Malika »
Bits Blitz - the place to be for all your bits needs!

Offline marell le fou

  • Full Member
  • *
  • Posts: 1107
Re: Modelling bits for 3d printing
« Reply #296 on: February 11, 2019, 07:47:18 PM »
A platipus ?

Offline Malika

  • Full Member
  • *
  • Posts: 1251
    • Loc: Netherlands
    • Bits Blitz
Re: Modelling bits for 3d printing
« Reply #297 on: March 11, 2019, 06:10:05 PM »
Quick experiment, 6mm harpoon tanks for the Skinners. Dunno if there would be any interest in this amongst Ork players:
Bits Blitz - the place to be for all your bits needs!

Offline Malika

  • Full Member
  • *
  • Posts: 1251
    • Loc: Netherlands
    • Bits Blitz
Re: Modelling bits for 3d printing
« Reply #298 on: March 11, 2019, 11:14:33 PM »
Bits Blitz - the place to be for all your bits needs!

Offline Malika

  • Full Member
  • *
  • Posts: 1251
    • Loc: Netherlands
    • Bits Blitz
Re: Modelling bits for 3d printing
« Reply #299 on: March 26, 2019, 09:49:02 PM »
Early WIP experiment of something I was pondering about whilst at work. This will most likely will have to be cast in resin. Dimensions per component: 25mm tall, 50mm wide, 47mm long.


Multiple next to one another, in combination with the street light kit and some models for scale:
Bits Blitz - the place to be for all your bits needs!